/* $Id: dram_init.S,v 1.12 2002/08/09 11:37:37 orjanf Exp $ * * DRAM/SDRAM initialization - alter with care * This file is intended to be included from other assembler files * * Note: This file may not modify r9 because r9 is used to carry * information from the decompresser to the kernel * * Copyright (C) 2000, 2001 Axis Communications AB * * Authors: Mikael Starvik (starvik@axis.com) * * $Log: dram_init.S,v $ * Revision 1.12 2002/08/09 11:37:37 orjanf * Added double initialization work-around for Samsung SDRAMs. * * Revision 1.11 2002/06/04 11:43:21 starvik * Check if mrs_data is specified in kernelconfig (necessary for MCM) * * Revision 1.10 2001/10/04 12:00:21 martinnn * Added missing underscores. * * Revision 1.9 2001/10/01 14:47:35 bjornw * Added register prefixes and removed underscores * * Revision 1.8 2001/05/15 07:12:45 hp * Copy warning from head.S about r8 and r9 * * Revision 1.7 2001/04/18 12:05:39 bjornw * Fixed comments, and explicitely include config.h to be sure its there * * Revision 1.6 2001/04/10 06:20:16 starvik * Delay should be 200us, not 200ns * * Revision 1.5 2001/04/09 06:01:13 starvik * Added support for 100 MHz SDRAMs * * Revision 1.4 2001/03/26 14:24:01 bjornw * Namechange of some config options * * Revision 1.3 2001/03/23 08:29:41 starvik * Corrected calculation of mrs_data * * Revision 1.2 2001/02/08 15:20:00 starvik * Corrected SDRAM initialization * Should now be included as inline * * Revision 1.1 2001/01/29 13:08:02 starvik * Initial version * This file should be included from all assembler files that needs to * initialize DRAM/SDRAM. * */ /* Just to be certain the config file is included, we include it here * explicitely instead of depending on it being included in the file that * uses this code. */ #include ;; WARNING! The registers r8 and r9 are used as parameters carrying ;; information from the decompressor (if the kernel was compressed). ;; They should not be used in the code below. #ifndef CONFIG_SVINTO_SIM move.d CONFIG_ETRAX_DEF_R_WAITSTATES, $r0 move.d $r0, [R_WAITSTATES] move.d CONFIG_ETRAX_DEF_R_BUS_CONFIG, $r0 move.d $r0, [R_BUS_CONFIG] #ifndef CONFIG_ETRAX_SDRAM move.d CONFIG_ETRAX_DEF_R_DRAM_CONFIG, $r0 move.d $r0, [R_DRAM_CONFIG] move.d CONFIG_ETRAX_DEF_R_DRAM_TIMING, $r0 move.d $r0, [R_DRAM_TIMING] #else ;; Samsung SDRAMs seem to require to be initialized twice to work properly. moveq 2, $r6 _sdram_init: ; Refer to ETRAX 100LX Designers Reference for a description of SDRAM initialization ; Bank configuration move.d CONFIG_ETRAX_DEF_R_SDRAM_CONFIG, $r0 move.d $r0, [R_SDRAM_CONFIG] ; Calculate value of mrs_data ; CAS latency = 2 && bus_width = 32 => 0x40 ; CAS latency = 3 && bus_width = 32 => 0x60 ; CAS latency = 2 && bus_width = 16 => 0x20 ; CAS latency = 3 && bus_width = 16 => 0x30 ; Check if value is already supplied in kernel config move.d CONFIG_ETRAX_DEF_R_SDRAM_TIMING, $r2 and.d 0x00ff0000, $r2 bne _set_timing lsrq 16, $r2 move.d 0x40, $r2 ; Assume 32 bits and CAS latency = 2 move.d CONFIG_ETRAX_DEF_R_SDRAM_TIMING, $r1 move.d $r1, $r3 and.d 0x03, $r1 ; Get CAS latency and.d 0x1000, $r3 ; 50 or 100 MHz? beq _speed_50 nop _speed_100: cmp.d 0x00, $r1 ; CAS latency = 2? beq _bw_check nop or.d 0x20, $r2 ; CAS latency = 3 ba _bw_check nop _speed_50: cmp.d 0x01, $r1 ; CAS latency = 2? beq _bw_check nop or.d 0x20, $r2 ; CAS latency = 3 _bw_check: move.d CONFIG_ETRAX_DEF_R_SDRAM_CONFIG, $r1 and.d 0x800000, $r1 ; DRAM width is bit 23 bne _set_timing nop lsrq 1, $r2 ; 16 bits. Shift down value. ; Set timing parameters. Starts master clock _set_timing: move.d CONFIG_ETRAX_DEF_R_SDRAM_TIMING, $r1 and.d 0x8000f9ff, $r1 ; Make sure mrs data and command is 0 or.d 0x80000000, $r1 ; Make sure sdram enable bit is set move.d $r1, $r5 or.d 0x0000c000, $r1 ; ref = disable lslq 16, $r2 ; mrs data starts at bit 16 or.d $r2, $r1 move.d $r1, [R_SDRAM_TIMING] ; Wait 200us move.d 10000, $r2 1: bne 1b subq 1, $r2 ; Issue initialization command sequence move.d _sdram_commands_start, $r2 move.d _sdram_commands_end, $r3 1: clear.d $r4 move.b [$r2+], $r4 lslq 9, $r4 ; Command starts at bit 9 or.d $r1, $r4 move.d $r4, [R_SDRAM_TIMING] nop ; Wait five nop cycles between each command nop nop nop nop cmp.d $r2, $r3 bne 1b nop move.d $r5, [R_SDRAM_TIMING] subq 1, $r6 bne _sdram_init nop ba _sdram_commands_end nop _sdram_commands_start: .byte 3 ; Precharge .byte 0 ; nop .byte 2 ; refresh .byte 0 ; nop .byte 2 ; refresh .byte 0 ; nop .byte 2 ; refresh .byte 0 ; nop .byte 2 ; refresh .byte 0 ; nop .byte 2 ; refresh .byte 0 ; nop .byte 2 ; refresh .byte 0 ; nop .byte 2 ; refresh .byte 0 ; nop .byte 2 ; refresh .byte 0 ; nop .byte 1 ; mrs .byte 0 ; nop _sdram_commands_end: #endif #endif